We engineer and manufacture double skinned oil tanks for outdoor use according to EN 12285. The sizes go up to 125m3. For indoors tanks according to SFS 2735 are also made in the size and shape you wish. Cylindrical tanks we manufacture according to EN 12285 and up to 125 m3. Rectangular indoor tanks based on SFS 2735 and special ones are tailored and the necessary structural approvals are taken care of with the local notified body.

The pressure vessels are designed, manufactured and inspected according to the pressure vessel directive 2014/68/EU, typically complying with the requirements for G-module.

The engineering, stress calculations and the whole design is at our hands and we will take care of the necessary approvals for the engineering and for the final product.

Hitting high and hard is always a beautiful way to load and discharge, but when considering wear, tear and dusting, it’s the opposite. By engineering the chute geometry correctly, wearing can be reduced to a great extent. If the material does not touch the walls, the wall will not wear and yes, you can actually calculate or simulate the material flow.

One way of preventing dust from spreading to the surroundings is the use of very fine water fog. When the droplets are so small that they don’t freeze in the winter air, but still catch the dust particles and drop them down. With droplet size below 0,1 mm, the amount of water used for example in a transfer point is less than 100 l/h, which is insignificant in comparison to the mass flow of material. The fog can be used on transfer points, discharge ends, door opening, hoppers … you name it, we do it.

The decontamination containers help in ensuring this target. When using disposable overalls, these can be removed either outside or on the dirty side, before washing the boots, hands and vacuum cleaning the clothes. Entrance to the clean side goes through an air shower, where high speed – low pressure air is used to detach dust from the clothes.

On the clean side it is time to remove the personal protection gear, clean it up once more and leave to the clean areas.

Our engineers will come to you, will be there during the installation and moderinsation. This gives a good foundation for the ideas, calculations and proposals for solutions that consider the conditions at site and help you make the most out of your production..  TUTUSTU

We do optimize each conveyor to it’s application so that the wear plates can be inspected and changes, the rollers can be quickly replaced also below the skirtboard sealing and the safety shields are easily removable. Every project, especially the installations generate always a few new ideas how we could make the solutions smarter, easier to install and more simple to use. The overall solution is one that will help to improve the availability of the production process and to minimize the operating expenses.

Our practical engineering team aims to design simple structures that are easy to manufacture accurately, but solutions that the installation and maintenance teams will know to appreciate. The installation locations often have their limitations with regards to transfers routes, lifting equipment etc. To avoid unpleasant surprised we are glad to come by and check the routes, lifting possibilities and to add the necessary lifting points or to design the equipment in suitable size elements. The small things like a bit larger maintenance hatches don’t really cost anything to manufacture, but over the lifetime can cause quite a bit of cost and pain.

We basically design anything, do the strength calculations, make the models, workshop drawings, material lists and documentation. And we do not fall in love with them, but share them happily to our customers and their maintenance organizations.

We do manufacture machines, equipment and structures based on the customer drawings. But, we prefer that you just provide us the spec a 3D model or some sketches and we pick it up from there. If you’re looking for the cheapest solutions, you might want talk to somebody else. But if safety, easy installation, maintainability and availability is of interest…we are the right ones to talk to.

Whether it is different types of conveyors, lifters, chutes, steel structure or other medium sized structures, let’s discuss.

Our production facility consists of 3000 m² production area with 3x 10 t lifting capacity makes it possible to build also a bit larger structures. Our wide range of cooperation partners and subsuppliers in Finland and abroad means we don’t normally run out of capacity.

Bending, rolling, machining, turning and welding capacity are inhouse, but some of this work is also subcontracted. Surface treatment and assembly are done inhouse practically always.

The LAPA-MIXER spares are to a very high degree compatible with the old LAPA-MIXER models. The wear and spare parts can be found in our stock and we’ll be glad to discuss with you also new material options for your production. In wear protection, there are nowadays quite a few alternatives.